U103-A Filter

U103-A Filter

This device is mainly applied in the system of dispenser to remove the solid sedimentation is the oil ,ensuring the cleaning of the oil or like ,and as a result to extend the life span and accuracy of the flow meter. In the system of dispenser ,it is fixed between the oil pump and the flow meter.

Materials:

Body: Body: Aluminum (Spray-Painted)

Seals: Buna-N

Technical Specifications:

Working pressure:0.2Mpa

Filter accuracy:30um

Flow Rate:65L/min

Rating Medium:Gasoline,Kerosene, Diesel

100% Factory Tested.

Package:

Product ID Net Weight Cross Weight Dimension

U103-A 2kg/case of1 2.2kg/case of1 20x13x14cm/case of1

Diagram 2-7: Installation of framework oil seal Important noti fuel dispenser ces to disassembly and reassembly As pump and motor are the resource of power one should pay much attention to disassembly and reassembly of pump. Be sure that cut power prior to maintenance. Disconnecting V belt in case to cause any accident, prepare a container to collect oil that will pollute environment. Grind the semicircle keyway on pump axis using sand paper before disconnecting pump cover in order not to scratch framework oil-seal by burr. All components should be carefully cleansed prior to reassembly of pump in case dirty substance flow into pump and cause new trouble. Turn rotor and examine the vane working state after installing rotor subassembly and spring in pump chamber. M fuel dispenser eanwhile, be sure that the position of vane should higher than rotor, low pump frame even. A little grease should be daubed on the inner of brass bushing and framework oil-seal when installing pump cover. When installing the bolts of pump cover each tension is coherent as the sequence that opposite bolts go first. After reassembly of pump to check inspect the rotation of pump. The seal ring between pump and vapor-recovery should be carefully examined before installing in case of leakage. Be sure that the two V wheels of motor and pump in line, having any obvious jump and wave. Internal gear pump Fuel dispenser is mounted now with two types of internal gear pump, namely, involute gear pump and inner cycloidal gear pump. In the former type a piece of crescent clapboard is installed between small gear and inner gear, dividing suction chamber with discharge chamber. However, i fuel dispenser n the latter type the division is realized through joint between gears, without clapboard. The smaller gear in internal gear pump is driver. Diagram 2-8 illustrate above gear pumps. Internal gear pump characterized that compact, light in weight, low noise and long service life still has disadvantage of complicated gear figure and high cost. Domestic market now has these two kin

SCCD. However it will be beneficial if the PCD can　　 fuel dispenser have a hardcoded value for many of these parameters.　　June 2005 IFSF - STANDARD FORECOURT PROTOCOL FP31_2.21　　 DISPENSER APPLICATION　　 Page: 113　　 8 bcd2 R(1-9) O　　 Meter_1_Blend_Ratio　　 (08H) (0-99) W(1-2)　　 Indicates the blend ratio in percentage of the first base　　 grade.　　 The blend ratio of the fuel dispenser second base grade is assumed to be　　 the remaining percentage.　　 0 = no blending　　 Please note that when the FP supports blending this　　 Data_Id must be implemented.　　 PCD Comment:　　 As this is an optional data field the PCD can NAK any　　 write requests to this Data_Id with a Data_ACK code of　　 4 (Data does not exist in this device) or reply to any read　　 request with an answer message with the respective　　 Data_Id s length set to 0.　　 9 bin8 R(1-9) O　　 Meter_2_Id　　 (09H) (0-16) W(1-2)　　 Indicates the meter identifier of the second base product.　　 The numbering of fuel dispenser the meters is manufacturer model　　 specific and must be defined separate.　　 0 = no 2nd meter used　　 Please note that when the FP supports blending this　　 Data_Id must be implemented.　　 Please note that dispensers that do not permit this Data_Id　　

them their most popular meeting-place, a blog called the Daily fuel dispenser Kos, attracts hundreds of writers and perhaps half a million readers a day. They are the most disruptive force in Democratic politics today. Their aim is to transform the party by backing candidates who will “fight back�against Mr Bush. Mr Lamont is top of their list. “Lieberman is going to lose,�said Markos Moulitsas Zúniga, the Daily Kos s 34-year-old founder, to a rapturous audience at a Kossack convention in Las Vegas this month. Mr Lamont is an amiable fellow. A banking heir and cable TV entrepreneur, he is worth more than $90m (he calls himself a “small businessman�. Despite his wealth, his policies are solidly progressive. He wants universal health insurance, more money for sc fuel dispenser hools and to save Social Security by raising taxes on the rich. On bread-and-butter issues, he is to the left of Mr Lieberman, but the difference is much smaller than his eager team of campaign workers would have you believe. The only real chasm between the two candidates policies is over Iraq. Mr Lieberman thinks America was right to overthrow the “primitive, killing tyranny of Saddam� On trips to Iraq, he sees progress towards “modern, self-governing, self-securing nationhood� And he thinks that whatever people think about the initial decision to go to war, the commander-in-chief should have bipartisan support to see it through to a successful conclusion. Mr Lamont thinks the war was wrong, rushed and botched. He says the $250m it costs each day would be better spent on education. Whereas Mr Bush says that American troops can stand down as the Iraqis stand up, Mr fuel dispenser Lamont thinks the opposite that the Iraqis “won t step up till we step back� He wants American troops to withdraw as quickly as is practical. He also urges the president to reassure Iraqis that America has no designs on their oil and no plans for permanent military bases in Iraq. These lines win hearty applause from the kind of Democrat who turns u